Proline Plus™ 200 Product Information
Proline Plus™ 200 is a medium-density, closed-cell, spray-applied, polyurethane foam insulation for use in residential, commercial, industrial and institutional structures. Sprayed in place as a liquid, a chemical reaction causes expansion to yield high-quality foam insulation.
Proline Plus™ 200 is formulated with recycled PET (polyethylene terephthalate) raw materials and meets or exceeds the standards set out in CAN/ULC S705.1-01, including Amendments 1 and 2, as referenced in the National Building Code of Canada. Proline Plus™ 200 is listed by NRC (National Research Council of Canada) under CCMC (Canadian Construction Materials Centre) listing #13545-L.
Application of Proline Plus™ 200 may be performed only by Trained Professionals adhering to the Urethane Foam Consultants (UFC) Field Quality Assurance Program and the CAN/ULC S705.2 application standard. Proline Plus™ 200 can be sprayed into walls, ceilings, floors, attics and crawl spaces. Excess insulation can be trimmed within seconds of spraying, allowing drywall and/or finishing surfaces to be installed as soon as the application is complete.
Proline Plus™ 200 is intended for use in residential, commercial, industrial and institutional building applications. It expands to seal cavities, while reducing heat migration, energy consumption and moisture gain in buildings.
Proline Plus™ 200 is designed for interior or exterior building envelope applications, above or below grade.
- Refer to the Proline Plus™ Installer’s Manual for instructions.
- Store in a well-ventilated area.
- Maintain storage temperature between 18–30º C (65–86º F).
- Do not heat above 60º C (140º F).
- Do not allow to freeze.
Containers & Storage
Proline Plus™ 200 is supplied in “material sets” consisting of two liquid components contained in 55-US-gallon drums. Component A, isocyanate, is in red drums. Component B, resin, is in white drums.
Components should be stored in a well-ventilated area, maintained between 18–30º C (65–86º F). Do not allow components to freeze. Do not heat components above 60º C (140º F).
For best results, Proline Plus™ 200 should be sprayed using 1000–1200 psi fluid pressure with materials heated to 49–54º C (120–130º F).
Trained Professionals spraying Proline Plus™ 200 can achieve yields between 10.6–11.8m3 (4500–5000 bd ft) of high-quality foam per material set.
Safe for Electrical Wiring
Proline Plus™ 200 can be applied over 14/3 and 12/2 wiring without affecting wire coverings.
Safe for Plumbing
Proline Plus™ 200 is safe for PVC (polyvinyl chloride), ABS (acrylonitrile butadiene styrene), PEX (cross-linked polyethylene), copper and steel piping systems.
Use Caution Near Heat-emitting Sources
Insulation must be kept away from heat-emitting devices, such as recessed light fixtures and chimneys, at the minimum distance required by building regulations and safety codes. Gap should never be less than 75mm (3”).
Does Not Support Bacteria or Fungi
Proline Plus™ 200 is not a source of nutrients or sustenance for bacteria or fungi. Air sealing provided by Proline Plus™ 200 prevents infiltration of moisture, nutrients and spores.
Does Not Support Insects, Rodents or Other Pests
Proline Plus™ 200 is not a source of food for insects, rodents or other pests.
Environmental Health & Safety
Proline Plus™ 200 is free of CFCs (chlorofluorocarbons) and HCFCs (hydro chlorofluorocarbons).
The Saskatchewan Research Council has tested Proline Plus™ 200 for VOCs (volatile organic compounds) off gassing and recommended extremely sensitive individuals delay occupancy for one day.
Proline Plus™ 200 Technical Information
|Density||ASTM D1622||2.07 – 2.3 ft/m3
|Aged Thermal Resistance
(50mm foam depth)
|ASTM C518||R 13.3
|Long Term Thermal Resistance
(50mm foam depth)
|CAN/ULC S 770||R 11.4
|Air Permeation @ 75 Pa||ASTM E2178||0.0006 L/S*m2|
|Water Vapour Permeance||ASTM E96||28 ng/(Pa•s•m2)|
|Water Absorption (% volume)||ASTM D2842||1.8%|
|Flame Spread||ULC S-102 Steiner Tunnel||Flame 6.2
|Corner Wall Test||ULC S-127||190|
(volume change after 28 days)
|ASTM D2126||-29ºC, 0.03%
70ºC @ 97% RH, 0.2%
|Compression Strength||ASTM 1621||27.6 psi
|Tensile Strength||ASTM 1623||43 psi, pass
297 kPa, pass
|Open Cell Content||ASTM D2856||6.4%|
|Fungal Resistance||ASTM G21||Zero Rating|
|VOC Emissions||CAN/ULC S774-09||1 day, pass|
|Revised January, 2015|
The physical and performance properties of Proline Plus™ 200 are determined through standardized tests conducted by certified independent third-party testing laboratories. Specifications may be revised periodically as development leads to product improvements.
The information, data and products presented herein are based upon information reasonably available to Winroc at the time of publication. The information is provided in good faith, but is not to be regarded as a guarantee, express or implied, of performance or results. Any application should be thoroughly tested to determine satisfactory performance.